Engineering, B.S.

The following Four-Year Roadmaps are meant to be a guide for students and academic advisors in planning a path to a degree within four years (eight semesters) if the student is able and willing to do so. The set of courses shown below are based exclusively on the Fall 2020 Catalog and the most up to date General Education (G.E.) Program in that catalog year. The requirements outlined may not apply to students in earlier catalog years, especially in the G.E. courses required in specific categories. Please note that courses identified in the Four -Year Roadmaps may not always be available during each of the prescribed semesters, therefore, it is always recommended to consult an academic advisor. Advisors may need to adjust the courses in the Four-Year Roadmap to keep students on track to graduate in four years.  

First Semester

AREA (as listed on TDA) COURSE UNITS 
Major Requirement
Mathematics and Science Courses
MATH150A
4
Major Requirement
Mathematics and Science Courses
CHEM123 
3
Major Requirement
Engineering Core Courses
EGME 102
2
G.E. subarea A.1
Oral Communications
 
3
G.E. subarea A.2
Written Communication
 
Total
 
15 

Second Semester

AREA (as listed on TDA) COURSE UNITS 
Major Requirement
Mathematics and Science Courses
MATH 150B
4
Major Requirement
Mathematics and Science Courses
PHYS 225
3
Major Requirement
Mathematics and Science Courses
PHYS 225L
1
Major Requirement
Engineering Core Courses
EGME 205
3
G.E. subarea C.1
Intro to the Arts
 
3
Total
 
14

Third Semester

AREA (as listed on TDA) COURSE UNITS
Major Requirement
Mathematics and Science Courses
MATH 250A 
4
Major Requirement
Mathematics and Science Courses
PHYS 226
3
Major Requirement
Mathematics and Science Courses
PHYS 226L
1
Major Requirement
Engineering Core Courses
EGCE 201
3
G.E. subarea C.2*
Intro to the Humanities
 
Total
 
14

*One course from C.2, C.3, D.1, D.4, or E should overlay with GE Overlay Z

Fourth Semester

AREA (as listed on TDA) COURSE UNITS
Major Requirement
Mathematics and Science Courses
MATH 250B
4
Major Requirement
Mathematics and Science Courses
PHYS 227
3
Major Requirement
Engineering Core Courses
EGME 304
3
Major Requirement
Engineering Core Courses
EGCE 302
3
G.E. subarea C.3*
Explorations in the Arts or Humanities
 
3
Total
 
16

*One course from C.2, C.3, D.1, D.4, or E should overlay with GE Overlay Z

Fifth Semester

AREA (as listed on TDA) COURSE UNITS
Major Requirement
Mathematics and Science Courses
EGME 308 OR EGCE 308 OR EGEE 308 OR EGGN 308
 3
Major Requirement
Upper-Division Writing Requirement
ENGL 360
3
Major Requirement
Engineering Core Courses
EGEE 203
3
A.A.T.C. (Advisor Approved Technical Course)
300 Level or 400 Level Course in Engineering or Computer Science 
G.E. subarea D.3
American Government
 
3
Total
 
15

Sixth Semester

AREA (as listed on TDA) COURSE UNITS
Major Requirement
Engineering Core Courses
EGEE 203L
1
A.A.T.C. (Advisor Approved Technical Course)
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course)
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
G.E. subarea D.2
American History
 
Total
 
16

Seventh Semester

AREA (as listed on TDA) COURSE UNITS
Major Requirement
Engineering Core Courses
EGCP 401 OR EGCE 401 OR EGEE 401 OR EGME 401
3
A.A.T.C. (Advisor Approved Technical Course)
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course)
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
G.E. subarea D.1*
Introduction to the Social Sciences
 
Total
 
15

*One course from C.2, C.3, D.1, D.4, or E should overlay with GE Overlay Z

Eighth Semester

AREA (as listed on TDA) COURSE UNITS
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
 3
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
A.A.T.C. (Advisor Approved Technical Course) 
300 Level or 400 Level Course in Engineering or Computer Science 
Total
 
15